Ich sehe gerade hier gibt es auch eine Linux-Abteilung und da ich mit meinem Problem in den deutschen Fachforen nicht weiter komme versuche ich es mal hier.
Ich bin von Mint 17.3 auf Mint 18 umgestiegen. Seit dem geht mein Internetstick nicht mehr. Er wird als Datenträger erkannt 1c9e:f000 und müsste umgeschalten werden auf 1c9e:9605
Kann jemand was mit dem Log-File anfangen und sagen wo ich ansetzen muss?
Ichhabe schon vieles probiert was im Internet steht, gebe ich "lsusb" ein steht da immer 1c9e:f000 ...
Code
- USB_ModeSwitch log from Wed Dec 14 23:09:19 2016
- Use global config file: /etc/usb_modeswitch.conf
- Started via systemd
- Raw args from udev: 3-2
- Bus ID for device not given by udev.
- Trying to determine it from kernel name (3-2) ...
- Use top device dir /sys/bus/usb/devices/3-2
- USB dir exists: /sys/bus/usb/devices/3-2
- SCSI dir exists: /sys/bus/usb/devices/3-2
- Warning: SCSI attribute "vendor" not readable.
- Warning: SCSI attribute "model" not readable.
- Warning: SCSI attribute "rev" not readable.
- Use interface /sys/bus/usb/devices/3-2/3-2:1.0
- ----------------
- USB values from sysfs:
- idVendor 1c9e
- idProduct f000
- manufacturer USB Modem
- product USB Modem
- serial 1234567890ABCDEF
- bNumConfigurations 1
- bConfigurationValue 1
- devnum 7
- busnum 3
- ----------------
- bNumConfigurations is 1 - don't check for active configuration
- Found packed config collection /usr/share/usb_modeswitch/configPack.tar.gz
- Searching entries named: /usr/share/usb_modeswitch/1c9e:f000*
- Searching overriding entries named: /etc/usb_modeswitch.d/1c9e:f000*
- SCSI attributes not needed, move on.
- match uMa
- match string: USB_Modem
- device string: USB Modem
- Extract config 1c9e:f000 from collection /usr/share/usb_modeswitch/configPack.tar.gz
- config: TargetVendor set to 1c9e
- config: TargetProduct set to 9000,9603,9605,9607,9900
- config: WaitBefore set to 1
- Driver module is "option", ID path is /sys/bus/usb-serial/drivers/option1
- Delay time of 1 seconds.
- wait is over, start mode switch.
- Unbinding driver
- Command to be run:
- /usr/sbin/usb_modeswitch -W -D -s 20 -c /run/usb_modeswitch/current_cfg -u -1 -b 3 -g 7 -v 1c9e -p f000 2>&1
- Verbose debug output of usb_modeswitch and libusb follows
- (Note that some USB errors are expected in the process)
- --------------------------------
- Read config file: /run/usb_modeswitch/current_cfg
- * usb_modeswitch: handle USB devices with multiple modes
- * Version 2.2.5 (C) Josua Dietze 2015
- * Based on libusb1/libusbx
- ! PLEASE REPORT NEW CONFIGURATIONS !
- DefaultVendor= 0x1c9e
- DefaultProduct= 0xf000
- TargetVendor= 0x1c9e
- TargetProductList="9000,9603,9605,9607,9900"
- MessageContent="555342431234567800000000000001ff000000000000000000000000000000"
- NeedResponse=0
- Success check enabled, max. wait time 20 seconds
- System integration mode enabled
- Use given bus/device number: 003/007 ...
- Look for default devices ...
- bus/device number matched
- found USB ID 1c9e:f000
- vendor ID matched
- product ID matched
- Found devices in default mode (1)
- Use interface number 0
- Use endpoints 0x01 (out) and 0x81 (in)
- USB description data (for identification)
- -------------------------
- Manufacturer: USB Modem
- Product: USB Modem
- Serial No.: 1234567890ABCDEF
- -------------------------
- Looking for active driver ...
- OK, driver detached
- Set up interface 0
- Use endpoint 0x01 for message sending ...
- Trying to send message 1 to endpoint 0x01 ...
- OK, message successfully sent
- Reset response endpoint 0x81
- Reset message endpoint 0x01
- ok:busdev
- --------------------------------
- (end of usb_modeswitch output)
- Check success of mode switch for max. 20 seconds ... Read attributes ...
- USB dir exists: /sys/bus/usb/devices/3-2
- idProduct doesn't match the expected value. ('9000,9603,9605,9607,9900' != 'f000')
- Attributes are different but target values are unexpected: idVendor: 1c9e
- idProduct: f000
- manufacturer: USB Modem
- product: USB Modem
- serial: 1234567890ABCDEF
- bNumConfigurations: 1
- bConfigurationValue: 1
- devnum: 7
- busnum: 3
- Mode switching was successful, found 1c9e:f000 (USB Modem: USB Modem)Now check for bound driver ...
- no driver has bound to interface 0 yet
- Device not in "bind_list" yet, bind it now
- Module loader is /sbin/modprobe
- Try to load module "option"
- Module was loaded successfully: 0
- Try to add ID to driver "option"
- ID added to driver; check for new devices in /dev
- driver binding failed
- Check for AVOID_RESET_QUIRK kernel attribute
- AVOID_RESET_QUIRK activated
- All done, exit
